CN
EN
Product Overview
ADM16F03A
ADM16F03 is a high-performance SoC with a clock frequency of up to 150MHz. It integrates an operational accelerator, operational amplifier, comparator, ADC, PWM controller, communication peripherals, pre driver, and 5V LDO; Support multiple motor drives
Datasheet →industry
Product Features
● Single source power supply
-12V~15V
- Integrated LDO (core 1.2V, digital IO port 5V, analog 3V)
● High performance 16 bit fixed-point DSP core
- Main frequency up to 100MHz
- Harvard bus structure
- Fast interrupt response and processing
● on-chip memory resources
-4K x 16 bit SARAM
- (256+256+32) x 16 bit DARAM
-32K x 16 bit Flash
● operation acceleration unit
- division, square root - arctangent
- Parker transform
-32-bit multiply add and shift
● 17 general-purpose I/O pins
● Event manager EM1
-4 16 bit timing/counters
-8 PWM outputs (PWM1-6 form 3 complementary groups, PWM7/8 independent)
-1 set of orthogonal encoding units
-3 capture units (CAP1/2/3)
- configurable PWM cycle interrupt generation and ADC sampling trigger timing
● integrated three-phase high and low side half bridge drive circuit
- six NMOS Pre Driver
- gate drive circuit high side maximum floating absolute voltage reaches 45V tag13} - Drive Capability IO+/IO -:+1.2A/2.0A VDRV=15V, VBS=15V
● ADC
-12 bits, conversion rate 1MSPS
-16 channels, with temperature sensor channels
- Channel Sorter, ADC can be set Sampling channel sequence
● Operational amplifier
-1 OP, can be used for bus current detection amplification
-3 PGAs, can be used for phase current detection amplification
● Voltage comparator
-3 voltage comparators, shared reference terminal, can be used for BEMF comparison detection
-2 voltage comparators with reference voltage (generated by DAC), Can be used to protect
● Interrupts
-2 external interrupts
-29 peripheral interrupts set by PIE
● Digital delay filtering
-3 Independently configure delay filtering units for external interrupts, power protection, and CAP1/2/3
● Serial communication peripherals
- SPI, SCI
● Clock
-10M on-chip oscillator
- PLL multiplication factor 1x~10x
● Supports WDT
● Supports 4-wire fast program burning
● Supports JTAG online simulation
- Analysis and breakpoint function
- Hardware based real-time debugging
● ESD level (HBM): 2000V
● MSL Humidity sensitivity level: 3
● Packaging form
- LQFP48 packaging
- QFN48 packaging
-12V~15V
- Integrated LDO (core 1.2V, digital IO port 5V, analog 3V)
● High performance 16 bit fixed-point DSP core
- Main frequency up to 100MHz
- Harvard bus structure
- Fast interrupt response and processing
● on-chip memory resources
-4K x 16 bit SARAM
- (256+256+32) x 16 bit DARAM
-32K x 16 bit Flash
● operation acceleration unit
- division, square root - arctangent
- Parker transform
-32-bit multiply add and shift
● 17 general-purpose I/O pins
● Event manager EM1
-4 16 bit timing/counters
-8 PWM outputs (PWM1-6 form 3 complementary groups, PWM7/8 independent)
-1 set of orthogonal encoding units
-3 capture units (CAP1/2/3)
- configurable PWM cycle interrupt generation and ADC sampling trigger timing
● integrated three-phase high and low side half bridge drive circuit
- six NMOS Pre Driver
- gate drive circuit high side maximum floating absolute voltage reaches 45V tag13} - Drive Capability IO+/IO -:+1.2A/2.0A VDRV=15V, VBS=15V
● ADC
-12 bits, conversion rate 1MSPS
-16 channels, with temperature sensor channels
- Channel Sorter, ADC can be set Sampling channel sequence
● Operational amplifier
-1 OP, can be used for bus current detection amplification
-3 PGAs, can be used for phase current detection amplification
● Voltage comparator
-3 voltage comparators, shared reference terminal, can be used for BEMF comparison detection
-2 voltage comparators with reference voltage (generated by DAC), Can be used to protect
● Interrupts
-2 external interrupts
-29 peripheral interrupts set by PIE
● Digital delay filtering
-3 Independently configure delay filtering units for external interrupts, power protection, and CAP1/2/3
● Serial communication peripherals
- SPI, SCI
● Clock
-10M on-chip oscillator
- PLL multiplication factor 1x~10x
● Supports WDT
● Supports 4-wire fast program burning
● Supports JTAG online simulation
- Analysis and breakpoint function
- Hardware based real-time debugging
● ESD level (HBM): 2000V
● MSL Humidity sensitivity level: 3
● Packaging form
- LQFP48 packaging
- QFN48 packaging
